Cornelius Ice Maker 620046139 User Manual

ED/DF2XX 30” CCM1530 Nordic Style Lid Kit Installation Instructions  
INSTALLATION INSTRUCTIONS  
ED/DF2XX 30” CCM1530 NORDIC SS STYLE LID KIT  
This Nordic style kit applies to the Cornelius 30” Wide CCM1530 Nordic ice maker.  
Item  
No.  
Part No.  
Name  
Icemaker Adapter Lid  
Qty.  
1
2
3
5
6
7
8
620046139  
620050521  
620051215  
50904  
1
1
2
1
8
1
1
Manual Fill Cover  
Icemaker Mounting Bracket  
RTV Sealant 3 oz. Tube  
# 10 x 1/2” Sheet Metal Screw  
620701601  
620204719INS Installation Instructions  
630500109 Bin Stat  
CAUTION: Disconnect electrical power to the dispenser before proceeding with the icemaker  
adapter kit installation.  
1.  
Position the icemaker adapter lid (item 1), flush with the rear of the cabinet, on the dispenser.  
2. Seal the icemaker base to the adapter lid as follows:  
A. Locate the icemaker 2 inches from the rear and flush with the sides of the lid. Run a bead of RTV  
inside the perimeter of the icemaker base so that the base will set on the RTV.  
B. Set the icemaker onto the lid. Note: If installing the icemaker from the front of the dispenser, use a  
piece of 1” PVC pipe or larger as a “roller” to slide the icemaker over the front mounting bracket of  
the manual fill cover.  
C. Wipe away any excess RTV.  
3. With the icemaker installed on top of the adapter lid, drill .147 diameter holes (# 26 drill) into the dis-  
penser cabinet using the slotted holes in the side flanges of the lid as templates. Be careful not to  
drill into the ice storage hopper. Use of a drill stop (1/4 in.) is recommended. Secure the lid to the  
cabinet with (4) # 10 sheet metal screws (item 6).  
4. Drill .147 diameter holes into the icemaker cabinet and adapter lid using the icemaker mounting  
brackets (item 3) as templates. Be careful not to drill into any icemaker component (con-  
denser, tubing, etc.). Secure the mounting brackets to the icemaker and adapter lid with the # 10  
sheet metal screws (item 6) provided in the kit.  
5.  
Install the wire form bracket, supplied with the bin stat kit (item 4), through the 5/8” diameter hole in  
the bottom of the ice maker. Wrap the eye of the wireform over the stud near the hole to the end of  
the wireform bracket and wrap the tube around the end of the bracket several times, insuring the  
tube is secure.  
NOTE: The bin stat must not interfere with the agitator rotation or in the path of ice falling from  
the icemaker. If it interferes with the agitator or in the path of ice, bend the bracket out of the way.  
6. Check that the automatic agitation timer, located in the dispenser’s electrical control box, is set for  
automatic fill cube ice. The control box is located behind the merchandiser. Remove the merchan-  
diser by lifting up on the sides to disengage the mounting “hooks” from the cabinet slots and rotate  
it forward. Refer to the label in the control box for setting agitation times.  
7. Install the manual fill cover (item 2) on the adapter lid (item 1). Insert the hinge pins into the pivot  
brackets on the adapter lid with the cover open. Check that cover opens and closes correctly.  
Release Date: October 5, 2007  
© 2007, IMI Cornelius Inc.  
Revision: A  
Publication Number: 620204719INS  
- 1 -  
 
ED/DF2XX 30” CCM1530 Nordic Style Lid Kit Installation Instructions  
FIGURE 2. Bin Stat  
© 2007, IMI Cornelius Inc.  
- 3 -  
Publication Number: 620204719INS  
 

Clarion CD Player FMC250 User Manual
COBY electronic TV DVD Combo TV DVD1390 User Manual
Concord Camera Digital Camera JD C31z3 User Manual
Crown Recording Equipment 35246 User Manual
Curtis Home Theater System HTIB1002 User Manual
Directed Audio Car Amplifier D2400 User Manual
Dynex TV Antenna DX LCD19 09 User Manual
Extron electronic Network Card HSA 222S User Manual
Extron electronic Stereo Amplifier RGB 580XI User Manual
Generac Power Systems Portable Generator 05402 User Manual