Garmin Fish Finder GHS 10 User Manual

VHF 100/200 Series Radio Installation Instructions  
These installation instructions are for the following VHF radios and handsets:  
North American Models  
VHF 100  
International Models  
VHF 100i  
VHF 200  
VHF 200i  
GHS 10  
GHS 10i  
Compare the contents of this package with the packing list on the box. If any pieces are missing, contact your Garmin® dealer immediately.  
Before you begin the installation:  
Read these instructions thoroughly.  
Gather the appropriate fasteners and tools.  
Verify that all cables can reach the radio mounting location.  
Wear safety goggles and a dust mask when drilling, cutting, or sanding.  
Product Registration  
Help us better support you by completing our online registration today. Go to http://my.garmin.com. Keep the original sales receipt, or a  
photocopy, in a safe place.  
Contact Garmin  
Contact Garmin Product Support if you have any questions while using your VHF 100/200 series radio. In the USA, go to  
www.garmin.com/support, or contact Garmin USA by phone at (913) 397.8200 or (800) 800.1020.  
In the UK, contact Garmin (Europe) Ltd. by phone at 0808 2380000.  
In Europe, go to www.garmin.com/support and click Contact Support for in-country support information, or contact Garmin (Europe) Ltd.  
by phone at +44 (0) 870.8501241.  
Warnings and Safety Notices  
Antenna Mounting and EME Exposure  
Your VHF radio generates and radiates radio frequency (RF) electromagnetic energy (EME). Failure to observe these guidelines may  
expose persons to RF radiation absorption exceeding the maximum permissible exposure (MPE).  
Garmin declares an MPE radius of 59 in. (1.5 m.) for this system, which was determined using 25 watts output to an omni-directional 9 dBi  
gain antenna. The antenna should be installed such that a distance of 59 in. (1.5 m) is maintained between the antenna and all persons.  
WARNING: Radio operators with cardiac pacemakers, life-support machines, or electrical medical equipment should not be exposed to excessive  
radio-frequency fields.  
WARNING: Operate the device in accordance with the instructions supplied.  
NotICe: The device complies with internationally recognized standards covering human exposure to electromagnetic fields from radio devices.  
NotICe: Check with local authorities for any antenna or operational restrictions that may apply.  
Safe Compass Distance  
Ensure that you install your VHF radio at least 20 in. (500 mm) from any compass. Test your compass to verify that it operates correctly  
when the radio is operating.  
VHF 100/200 Series Dimensions  
Flush Mount—(W × H × D) 7.16 × 3.86 × 6.42 in. (18.2 × 9.8 × 16.3 cm)  
Bail Mount—(W × H × D) 7.56 × 4.65 × 6.42 in. (19.2 × 11.8 × 16.3 cm)  
July 2009  
190-01019-02 Rev. E  
 
Printed in China  
Flush Mounting the VHF 100/200 Series Radio  
In addition to the four included 4.2 × 25 mm, panhead mounting screws, flush mounting the VHF 100/200 series radio requires the  
following tools (not included):  
Phillips screwdriver  
Drill and 9/64 in. (3.5 mm) drill bit for mounting holes  
3/8 in. (10 mm) drill bit for a starter hole  
Jigsaw  
Scissors and tape  
Center punch and hammer  
File and sandpaper  
Anti-seize lubricant (optional)  
Note: Ensure that the surface on which you mount the VHF 100/200 series radio has sufficient open space behind it to accommodate the radio  
and the connected cables. There should be at least 5 in. (127 mm) of clearance behind the case.  
To flush mount the VHF 100/200 series radio:  
1. Cut and trim the flush-mount template (page 9) and ensure it will fit in the location where you want to flush mount the VHF 100/200  
series radio.  
2. Tape the flush-mount template to the mounting location.  
3. Use the center punch to indent the center of each of the four mounting-hole locations.  
4. Use a 9/64 in. (3.5 mm) drill bit to drill the four mounting holes.  
Gasket  
5. Use a 3/8 in. (10 mm) drill bit to drill a starter hole inside the corner of the template to  
begin cutting the mounting surface.  
6. Use the jigsaw to cut the mounting surface along the inside of the dashed line indicated  
on the template. Use a file and sandpaper to refine the size of the hole.  
7. Place the radio into the cutout to confirm that the four mounting holes are correct after  
refining the hole. If not, mark the correct locations of the four mounting holes. Remove the  
radio from the cutout.  
8. Apply the gasket to the back of the VHF 100/200 series radio.  
9. If the top and bottom snap covers are attached to the front of the VHF 100/200 series radio, re
by unsnapping the covers from the sides.  
10.Place the VHF 100/200 series radio into the cutout.  
11.Securely tighten the four mounting screws through the VHF 100/200 series radio into the drilled mounting holes.  
Snap covers  
Note: Stainless-steel screws may bind when screwed into fiberglass and overtightened. Garmin recommends applying an anti-galling, stainless,  
anti-seize lubricant to the screw before using.  
12.Place the snap covers over the mounting screws.  
VHF 100/ꢀ00 Series Radio Installation Instructions  
 
Step 3: Connect the VHF 100/200 Series Radio to Power  
The VHF 100/200 series radios have a power-cable wiring harness that connects to power and provides interface capabilities for connecting  
external devices.  
Notes:  
The replacement fuse on the power cable wiring harness is a 10 A, slow-blow fuse.  
If it is necessary to extend the power wires, use 18 AWG wire.  
If your boat has an electrical system, you might be able to wire the radio directly to an unused holder on your current fuse block. If you  
are using the fuse block, remove the in-line fuse holder supplied with the radio. You can also wire the radio directly to the battery.  
10 A fuse  
Boat ground  
To 10.8-15.6 Vdc  
boat supply  
-
To VHF 100 or  
ꢀ00 series radio  
+
Fuse Block  
CAUtIoN: The VHF 100/200 series radio maximum input voltage is 15.6 Vdc. Do not exceed this voltage, because this can damage the radio and  
void the warranty.  
Note: During a typical installation, use only the red and black wires. The other wires are used for NMEA 0183 and other connections, and do not  
have to be connected for normal operation of the radio. For information on connecting to a NMEA 0183-compatible device, see page 5.  
To install the power-cable wiring harness:  
1. Use a test light or voltmeter to determine the polarity of the voltage source.  
2. Connect the red (+) wire on the power-cable wiring harness to the positive voltage terminal on the battery. (If you use the fuse block on  
the boat, route the positive connection through the fuse, as shown on the Fuse Block diagram.)  
3. Connect a ground wire (not included) from the ground connector screw to the negative voltage terminal on the battery, using 18 AWG  
wire.  
Ground connector  
screw  
4. Connect the black (-) wire on the power-cable wiring harness to the negative voltage terminal on the battery.  
5. Install or check the 10 A fuse (on the fuse block or in the in-line holder).  
6. Connect the power-cable wiring harness red and black wires to the red and black wires on the back of the radio (connect the two red  
wires together and the two black wires together).  
CAUtIoN: Cover the connections with a waterproof, adhesive tape, such as rubber vulcanizing tape, to prevent water from  
seeping into the radio.  
VHF 100/ꢀ00 Series Radio Installation Instructions  
 
 
Step 4: Connect the VHF 100/200 Series Radio to an Antenna  
Connect a marine VHF antenna to the radio using the antenna port on the rear panel of the radio. Mount the antenna according to the  
installation instructions provided with the antenna.  
Antenna port  
Step 5: Mounting the Microphone Hanger  
Drill the mounting holes using a 1/8 in. (3 mm) drill bit. Use three of the included 3.5 × 20 mm, panhead mounting screws to  
mount the microphone hanger in a convenient location near the radio.  
Connecting the VHF 100/200 Series Radio to a Chartplotter (Optional)  
The VHF 100/200 series radio can be connected to a chartplotter so that data such as DSC information can be displayed on a chartplotter.  
Additionally, location information from the GPS function of the chartplotter can be displayed on the radio.  
A VHF 100/100i or 200/200i radio can be connected to a NMEA 0183-compliant chartplotter. A VHF 200 or 200i can be connected to a  
NMEA 2000®-compliant chartplotter.  
Connecting a VHF 100/200 Series Radio to a NMEA 0183-Compliant Chartplotter  
The following diagram illustrates the NMEA 0183 wiring used to connect your VHF 100/200 series radio to a GPS chartplotter. If  
additional cabling is necessary, go to http://buy.garmin.com.  
VHF 200 or 200i radio only—Attach the included 59 in. (1.5 m) NMEA 0183 extension cable to the cable on the rear panel of the radio.  
The other end of the extension cable has bare wires.  
Connect NMEA 0183 bare wires as indicated in the following illustration.  
Battery  
10.8 - 15.6 Vdc  
VHF 100/ꢀ00  
series radio  
+
-
Chartplotter  
Red—Power (+)  
Black—Power (-)  
Power  
cable  
Power +  
Power -  
Purple—Rx A (+)  
Tx A (+)  
>
>
>
NMEA  
cable  
Gray—Rx A (-)  
Blue—Tx A (+)  
Tx A (-)  
>
Rx A (+)  
>
>
>
Brown—Tx B (-)  
Rx B (-)  
>
CAUtIoN: Cover the connections with a waterproof, adhesive tape, such as rubber vulcanizing tape, to prevent water from seeping into the radio.  
The VHF 100/200 series radio can receive and transmit the following NMEA 0183 sentences (version 3.01) from a NMEA 0183-compliant  
device:  
Sentence  
(Receive)  
Definition  
Sentence  
(Transmit)  
Definition  
GGA  
GLL  
Global Positioning System Fix Data  
DSC  
DSE  
DSC Information  
Geographic Position (Latitude and Longitude)  
GNSS (Global Navigation Satellite System) Fix Data  
Recommended Minimum Specific Loran-C Data  
Recommended Minimum Navigation Information  
Recommended Minimum Specific GNSS Data  
Expanded DSC  
GNS  
RMA  
RMB  
RMC  
VHF 100/ꢀ00 Series Radio Installation Instructions  
 
5
       
Connecting a VHF 200 Series Radio to a NMEA 2000 network  
The VHF 200 and VHF 200i radios can be connected to your existing NMEA 2000 network, or you can build a basic NMEA 2000 network  
to connect to another NMEA 2000-compatible device, such as a chartplotter. For more information on NMEA 2000 and to purchase  
required connectors, visit www.garmin.com.  
Note: The VHF 100 and VHF 100i radios cannot be connected to a NMEA 2000 network. See page 5 to connect your radio to a NMEA 0183  
network.  
To connect the VHF 200 series radio to your existing NMEA 2000 network:  
1. Determine where you would like to connect the radio to your existing NMEA 2000 backbone.  
2. Disconnect one side of a NMEA 2000 T-connector from the backbone at an appropriate location.  
If you need to extend the NMEA 2000 backbone, connect an appropriate NMEA 2000 backbone extension cable to the side of the  
T-connector you disconnected.  
3. Add a T-connector (not included) for the radio in the NMEA 2000 backbone by connecting it to the side of the T-connector you  
disconnected.  
4. Route a NMEA 2000 drop cable (not included) to the bottom of the T-connector added in step 3 to your NMEA 2000 network. Use a drop  
cable with a length up to 20 ft. (6 m).  
5. Connect the drop cable to the T-connector and the NMEA 2000 port on the radio  
NMEA ꢀ000 port  
CAUtIoN: If you have an existing NMEA 2000 network on your boat, it should already be connected to power. Do not connect an additional  
NMEA 2000 power cable to an existing NMEA 2000 network, because only one power source should be connected to a NMEA 2000 network.  
VHF ꢀ00 series  
radio  
NMEA ꢀ000  
chartplotter  
Other NMEA  
ꢀ000 device  
Drop cable  
T-connectors  
NMEA ꢀ000  
backbone  
Connecting the VHF 200 Series Radio to an Existing NMEA 2000 Network  
To create a basic NMEA 2000 network:  
1. Connect two T-connectors (not included) together by their sides.  
2. Connect a NMEA 2000 power cable (not included) to one of the T-connectors.  
CAUtIoN: A NMEA 2000 power cable must be connected to a 12 Vdc power source through a switch. The VHF 200 series radio may drain your  
battery if it is connected directly. Connect the cable to the ignition switch of the boat if possible, or through an appropriate additional switch.  
3. Connect a NMEA 2000 drop cable (not included) to the other T-connector and to the NMEA 2000 port on the radio.  
6
VHF 100/ꢀ00 Series Radio Installation Instructions  
 
4. Add additional T-connectors for each device you want to add to the NMEA 2000 network, and connect each device to a T-connector with  
a drop cable.  
5. Connect terminators (not included) to each end of the combined T-connectors.  
Ignition or in-line  
switch  
Fuse  
NMEA ꢀ000  
device  
+
-
Drop cable  
1ꢀ Vdc battery  
Power cable  
T-connectors  
Female  
terminator  
Male  
terminator  
Creating a Basic NMEA 2000 Network  
NMEA 2000 PGN information  
Use this table to determine the approved NMEA 2000 PGN information that can be received and transmitted by a VHF 200 series radio  
when communicating with a NMEA 2000-compliant device.  
Receive  
Transmit  
059392  
059904  
060928  
126208  
129026  
ISO Acknowledgment  
059392  
060928  
126208  
ISO Acknowledgment  
ISO Address Claim  
ISO Request  
ISO Address Claim  
NMEA Request/Command/  
Acknowledge Group Function  
NMEA - Command/Request/Acknowledge Group Function  
COG (course over ground) and SOG (speed over ground)  
- Rapid Update  
126464  
126996  
129799  
129808  
PGN List  
Product Information  
Radio Frequency/Mode/Power  
DSC Call Information  
129029  
GNSS (Global Navigation Satellite System) Position Data  
Garmin VHF 200 Series radios are NMEA 2000 certified.  
Connecting the VHF 200 Series Radio to a Hailer Horn (Optional)  
The radio can be connected to a hailer horn that will allow using the microphone or the GHS 10 handset to make announcements through  
your public address system.  
To mount the hailer horn, refer to the installation instructions that came with the device. Mount the hailer horn at least 10 ft. (3 m) away  
from the microphone and facing away from the microphone to avoid feedback.  
To connect the VHF 200 series radio to a hailer horn:  
1. Attach the included 23 in. (600 mm) hailer cable to the cable on the rear panel of the radio by connecting the red RCA plug into the red  
jack.  
2. Connect the white wire on the other end of the hailer cable to the positive (+) connection on the hailer.  
3. Connect the black wire to the negative (-) connection on the hailer.  
CAUtIoN: Cover the connections with a waterproof, adhesive tape, such as rubber vulcanizing tape, to prevent water from  
seeping into the radio.  
Refer to the VHF 100/200 Series Owners Manual to operate the hailer.  
VHF 100/ꢀ00 Series Radio Installation Instructions  
 
 
Connecting the VHF 100/200 Series Radio to an External Speaker (Optional)  
The radio can be connected to an external speaker that allows you to hear your radio at a remote location. To mount the external speaker,  
refer to the installation instructions that came with the speaker.  
To connect the VHF 100 series radio to an external speaker:  
1. Connect the yellow wire on the wiring harness (located on the rear panel of the radio) to the positive (+) connection on the external  
speaker.  
2. Connect the green wire to the negative (-) connection on the external speaker.  
To connect the VHF 200 series radio to an external speaker:  
1. Attach the included 23 in. (600 mm) speaker cable to the cable on the rear panel of the radio by connecting the white RCA plug into the  
white jack.  
2. Connect the yellow wire on the other end of the speaker cable to the positive (+) connection on the external speaker.  
3. Connect the green wire to the negative (-) connection on the external speaker.  
CAUtIoN: Cover the connections with a waterproof, adhesive tape, such as rubber vulcanizing tape, to prevent water from  
seeping into the radio.  
Connecting the GHS 10 or GHS 10i Handset or a Relocation Microphone  
to the VHF 200 Series Radio (Optional)  
Use the microphone relocation port on the rear panel of the VHF 200 series radio to connect either a relocation microphone or a Garmin  
GHS 10 handset.  
Connecting a Relocation Microphone for the VHF 200 or VHF 200i  
To relocate the VHF 200 series radio detachable microphone, you can order a microphone relocation kit at http://buy.garmin.com, which  
consists of a 32.8 ft. (10 m) extension cable, a weather cap for the front microphone connector, and the necessary cable hardware.  
To connect the relocation microphone:  
1. Connect the extension cable to the microphone relocation port on the rear of the radio.  
Microphone  
relocation port  
2. Connect the other end of the extension cable to the relocation microphone.  
Connecting a GHS 10 or GHS 10i Handset  
You can use a Garmin GHS 10 handset with the VHF 200 radio, or a Garmin GHS 10i handset with the VHF 200i radio. The handset  
comes with a 32.8 ft. (10 m) extension cable, a cable mounting plate, a weather cap, and the necessary cable hardware. You can order a  
GHS 10 or GHS 10i handset at http://buy.garmin.com.  
Install the GHS 10 or GHS 10i handset at least 20 in. (500 mm) from any compass.  
To connect the GHS 10 or GHS 10i handset:  
1. Use the three 3.5 × 20 mm, panhead mounting screws to mount the bulk head plate where the handset will be located.  
2. Connect the extension cable to the microphone relocation port on the rear of the VHF 200 or VHF 200i radio.  
3. Use the bulk head plate to mount the other end of the extension cable and connect the extension cable to the handset.  
To connect an external speaker next to the GHS 10 or GHS 10i handset:  
The green and yellow wires on the extension cable can be used to connect an external speaker. Connect the yellow wire to the positive (+)  
connection on the external speaker. Connect the green wire to the negative (-) connection on the external speaker.  
Refer to the VHF 100/200 Series Owners Manual to operate the GHS 10 or GHS 10i handset.  
The CE Notified Body number (0168) is valid for the VHF 100i and VHF 200i only.  
0168  
8
VHF 100/ꢀ00 Series Radio Installation Instructions  
 
   
VHF 100/200 Series Flush-Mount Template  
VHF 100/ꢀ00 Series Radio Installation Instructions  
 
 
© 2009 Garmin Ltd. or its subsidiaries  
Garmin International, Inc.  
1200 East 151st Street, Olathe, Kansas 66062, USA  
Garmin (Europe) Ltd.  
Liberty House, Hounsdown Business Park, Southampton, Hampshire, SO40 9LR UK  
Garmin Corporation  
No. 68, Jangshu 2nd Road, Shijr, Taipei County, Taiwan  
190-01019-02 Rev. E  
July 2009  
Printed in China  
 

Cobra Electronics Automobile CJS 50 User Manual
Craftsman Trimmer 31679617 User Manual
Creda Plumbing Product OTRC300 User Manual
Dukane Projector 8928 User Manual
Ericsson Router W21 User Manual
Euro Pro Food Processor EP90E User Manual
Everpure Water System 7TO User Manual
GE Answering Machine 2 9827 User Manual
GE Monogram Microwave Oven JET343G User Manual
Generac Power Systems Portable Generator 05681 User Manual